HDR landscape

I need a place to post some of these picots I’ve been taking and this seemed to be as good as spot as any:)

 

Shopbuilt – tool wall

 

This is a really fun project that is ever expanding. The idea was to make each holder unique as well as pleasant to look at.

Drill bit storage
Drill bit storage
Instead of just screwing a hole into the wall i are walnut wall mounts for anything that need to hang,
Instead of just screwing a hole into the wall i are walnut wall mounts for anything that need to hang,
More hanging storage.
More hanging storage.
Clamp rack for small clamps
Clamp rack for small clamps
Holder for screwdrivers
Holder for screwdrivers
Chisel holder
Chisel holder
Calliper holder
Calliper holder
wrench holder
wrench holder
Yape measure holder
Tape measure holder



hammer holder
hammer holder

DSC_1293 DSC_1291 DSC_1285

Shopbuilt – Tenoning Jig

This tenoning jig was inspired by the micro jig dovetail clamps. I seen the clamps scrolling through instagram and I thought I could probably come up with a use for them. The tenoning jig is self positioning for any mortise and tenon that requires the the mortise to be in the exact centre, like a cabinet door.

The jig is contracted using 3/4" plywood
The jig is contracted using 3/4″ plywood
To use the jig you first zero it by moving the front fence till it just kiss the blade and lock it. then move the reference plate into the mortise, tight against one side and the rear fence. than tabour first pass. now you can flip your workpiece and repeat. Had to explain, easier to watch the video:)
You’ll have to watch the video to see how it works because it to hard to explain:)
The rear fence is use to rest the stock against when referencing a mortise
The rear fence is use to rest the stock against when referencing a mortise
A piece of 1/8" flat bar is used to reference one side of a mortise when resting against the rear fence
A piece of 1/8″ flat bar is used to reference one side of a mortise when resting against the rear fence
Once mortise is referenced you can lock it.
Once mortise is referenced you can lock it.
I used cutting boards material as runners
I used cutting boards material as runners
runner slots are just dados
runner slots are just dados
Mircojig clamps are used to hold the workpiece.
Mircojig clamps are used to hold the workpiece.

Dovetail clamp
Dovetail clamp





 

 

Martyn Booth

Shopbuilt – Wooden lathe





Super fun project! this lathe was made from the parts of an old cheap drill press.

The can turn a spindle 32" long
The can turn a spindle 32″ long

The shaft from the drill press is tapered.
The shaft from the drill press is tapered.
Can easily use the original drill chuck.
Can easily use the original drill chuck.
Have to drill a tapered hole for any attachments, luckily i have the correct tapered drill bit.
Have to drill a tapered hole for any attachments, luckily i have the correct tapered drill bit.
Step pulley,s from the drill press
Step pulley,s from the drill press
Maple tail stock, made a bronze wheel and lock collar
Maple tail stock, made a bronze wheel and lock collar
Adapter plate to adjust belt tension and speed
Adapter plate to adjust belt tension and speed
tool rest locks in-between the rails
tool rest locks in-between the rails
Tool rest is made from maple
Tool rest is made from maple
Tool rest is made to turn 360 degrees
Tool rest is made to turn 360 degrees
1/8" flade bar for the tool rest
1/8″ flade bar for the tool rest
Head stock is just layers of plywood. Two locking bolts to hold the spindle in place
Head stock is just layers of plywood. Two locking bolts to hold the spindle in place
Tailstock has a threaded rod with a sharpe point for a dead centre
Tailstock has a threaded rod with a sharpe point for a dead centre

Shopbuilt- Tapering jig

 

 

 

A table saw tapering jig is pretty handy to have around the shop to not only make tapers but to also joint an edge on a board.

tapering jig

measures 12″ by 40″



DSC_1200
Homemade hold down clamps
DSC_1201
Home made wing nuts using a barrel nut

 

Cutting board is used for a runner
Cutting board is used for a runner
Adjustable fence
Adjustable fence
wing nut
wing nut
hold down clamp
hold down clamp
Fence is relieved for a T-track bolt
Under side of Fence is relieved for a T-track bolt